Hi everybody , just wondering if anybody has experienced any issues the drivers of files while using NINA ? for example Executable files? i keep getting an error message while in NINA "Executable not found" and i don't know what to make of this message , any help would be appreciated ,thank you
Error message in NINA ,what is this?
Can be that you pointed one of the supporting services to a incorrect location and therefore it cannot find the relevant executable to launch. As an example if you have PHD2 in C:\PHD2 but you have NINA pointing to C:\Program Files\PHD2 it could give that error
This is just a random guess on my part
This is just a random guess on my part
Thank you Sean and Allan ,i decided to uninstall NINA and reinstall ,but now the cameras are not detected ,i even tried them with the asiair pro and my ipad and still would'nt show either , any ideas ? thanks in advance
nelson:
Thank you Sean and Allan ,i decided to uninstall NINA and reinstall ,but now the cameras are not detected ,i even tried them with the asiair pro and my ipad and still would'nt show either , any ideas ? thanks in advance
Hi Nelson, if you could give a run down of all the gear you are trying to use and how you have connected it. That would make it a lot easier to troubleshoot over the internet.
Also to check you installed all the latest drivers, ascom platform and other needed software.
Camera's not showing up sounds like a cable/power issue, but could very well be a driver issue also
Concise
Hi Sean ,sorry for the delay ,ok , first of i am using an Eqr6-pro , Red Cat 51 , zwo 120 mm (guide cam) and guide scope , ASI air 183 pro MC (imaging color cam)
,ZWO focuser ,ZWO ASI air pro connected to the imaging cam and the guide cam and the mount and the asiair pro is connected directly to the zwo power supply
when using just the ASIair pro with my Ipad , however when ipad is not in use , i connect the above equipment to a Minix mini PC, which has Carte du Ciel ,Stellarium ,Astap ,APT, Sequence Generator pro, NINA, Backyard EOS,Nebulosity,PHD2 ,Asi cams, SharpCap pro, Gimp , ill post if i forgot anything else , i must say that some of the error messages the have popped up on NINA are ,
,ZWO focuser ,ZWO ASI air pro connected to the imaging cam and the guide cam and the mount and the asiair pro is connected directly to the zwo power supply
when using just the ASIair pro with my Ipad , however when ipad is not in use , i connect the above equipment to a Minix mini PC, which has Carte du Ciel ,Stellarium ,Astap ,APT, Sequence Generator pro, NINA, Backyard EOS,Nebulosity,PHD2 ,Asi cams, SharpCap pro, Gimp , ill post if i forgot anything else , i must say that some of the error messages the have popped up on NINA are ,
Nelson, I have had this happen to my system in the past. I reinstalled ascom, and because I run system off 30 foot powered USB cable, found it all errors stopped when replacing cable with new one. (have a few as spares). Also, you may have defective connectors.
Steve Perry
Steve Perry
Concise
I did change cables ,but what i was thinking was uninstall the programs the are giving problems ,and reinstall them , the imaging camera is not being detected only on v2 simulator and this only happened the other day , i dont know whats going on
nelson:
Hi Sean ,sorry for the delay ,ok , first of i am using an Eqr6-pro , Red Cat 51 , zwo 120 mm (guide cam) and guide scope , ASI air 183 pro MC (imaging color cam)
,ZWO focuser ,ZWO ASI air pro connected to the imaging cam and the guide cam and the mount and the asiair pro is connected directly to the zwo power supply
when using just the ASIair pro with my Ipad , however when ipad is not in use , i connect the above equipment to a Minix mini PC, which has Carte du Ciel ,Stellarium ,Astap ,APT, Sequence Generator pro, NINA, Backyard EOS,Nebulosity,PHD2 ,Asi cams, SharpCap pro, Gimp , ill post if i forgot anything else , i must say that some of the error messages the have popped up on NINA are ,
The ZWO drivers should all be compatible, but I would first reinstall Ascom and connect each piece of hardware one at a time to figure out what is giving the error. Also check in mini pc settings for USB if they are allowed to powerdown when idle (Not 100% on the terminology) update usb drivers also just to make sure. Can’t comment on the eqr6-pro I am only familiar with the iOptron mounts
and here's one of my rigs
Problem with my Astrophysics Mount
Hi all, I have encountered a weird problem with my Astrophysics GTO 900 mount with the GTOCP2 control box. I am using the original v2 Driver. The Problem I came across behaves like explained in the following. For Imaging I use the newest Version of A...
NINA driver issues with executable files directly relevant to poster's problem.
Optimising a C8 for APS-C. - Drawtube v Celestron Focus Motor
I am currently using a Celestron Focus Motor and getting pretty good focus runs in NINA, good enough for imaging purposes but always looking for ways to improve. My focus runs just aren't consistent enough for the miniscule tilt adjustments I'...
NINA focus runs mentioned; may contain driver or software troubleshooting insights.
Autoguiding Issues
I didn't realize that cutting and pasting from Word would cause formatting problems… Hi, I am hoping that you can help me with autoguiding issues that I have been experiencing. Normally, my autoguiding is consistently good, with values abou...
Autoguiding issues in NINA context; potential driver or executable configuration solutions.
Mac Autoguiding
Hey everyone! I just got my first guide camera (ZWO ASI 120MM and a 30mm f/4 guide scope) and finally upgraded my skyview pro mount with a goto system.I do not use windows (I'm not an elitist or anything, I used to do radio astronomy for work, an...
NINA is autoguiding software alternative; discusses driver issues relevant to Mac setup.